Hammer Pulverizer of Sodium Gluconate

With the continuous increase in social needs, Hammer Pulverizer of Sodium Gluconate continues to improve in the use of performance, finished product quality, service life, etc., very good to process raw materials into micro-powder and even nanoscale fine powder, and are already chemical , Food, pesticides, cosmetics, dyes, coatings, electrons, etc. have been widely used.

The following is a detailed description:

1. Feed granularity control

Most Hammer Pulverizer of Sodium Gluconate has a certain upper limit requirement for the feed particle size. After entering the pulverization cavity, it can be sufficiently accelerated before collision and crushing with other particles. It is difficult to completely accelerate after large particles enter the pulverized cavity, which will allow them to stay in the machine too long, resulting in too high energy consumption. Therefore, in large-scale production of ultrafine powder, it is an effective way to pre-ground the raw material of the particle size is an effective pathway for energy saving.
2. Working medium

Currently, the working medium of Hammer Pulverizer of Sodium Gluconate is mainly compressed, superheated steam, inert gas, and the like. The choice of working fluid has a certain impact on crushing effects and economics. Superheated steam is superior to air in fluidity and critical flow rates to achieve higher flow rates and uniform flow fields. However, using superheated steam as a working fluid, it must be ensured that it is still in an overheating state before entering the product capture device, otherwise the material is condensed.
3. Feeding speed

Feeding speed is an important parameter reflecting gas flow grinding production capacity. During the pulverization process, the optimum ratio of the intake flow rate and the feed speed is the key to improving the crushing efficiency. In general, under certain intake flow conditions, the feed speed is proportional to the particle size of the product. However, the feeding speed is too fast, which will increase the particle density, mutual interference, disadvantage of the particles, and difficult to achieve the sufficient and effective collision between particles, affect the crushing effect; although the feed speed is too slow, the particles stay in the crush area The time can be extended, which will reduce the particle density, reduce the collision rate, resulting in a decrease in production capacity and an increase in unit production energy consumption.
4. Granular limit

Hammer Pulverizer of Sodium Gluconate In the pulverization process, as the material particle size is reduced, the crystallization and intensity of the material increases. After reaching a certain degree, the particle size of the material is no longer reduced or reduced, that is, the crushing limit of the material is reached.At this time, the material specific surface area increases, the surface activity of the particles, the particle agglomeration and grinding are in a dynamic equilibrium state, even if the grinding time is prolonged, it is difficult to further reduce the particle size of the material.


ALPA Long Stone Powder Hammer Pulverizer Of Sodium Gluconate Case Sharing: The company is a high-tech industry in one industrial company, integrating mineral resources, mining, deep processing in one, main products have six major products. Category: long stone powder, silicon fine powder, aluminum soil, kaolin and other products. The product is high, the particle size, reasonable particle size distribution, stable quality, widely used in electrician, electronics, silicone rubber, ceramics, precision casting and other industries. Products are exported to many countries and regions in my country. The company needs airflow selection to ultrafine long stone powder.
Finally, our classifier can meet customer needs.
Product particle size: D50: 16.7

1. Before using the pulverizer, first check whether all fasteners of the machine are tightened and the belt is fastened.
2. The spindle direction must be consistent with the direction of arrow on the shroud, otherwise it may damage the machine and cause personal injury.
3. Check if the crusher is complete.

5. You must check the purity of the material before crushing. Metal hard materials are not allowed to avoid damage to the tool or cause combustion.
6. The oil cup on the machine should always note the full lubricant to ensure that the machine is operating normally.
7. Stopping before stopping. If you do not continue, remove the residers from the machine.
8. Regular inspection tools and screens are damaged. If damage is damaged, it should be replaced immediately.
9. There will be slight vibration when using the fuselage. Be sure to tighten the cover to connect the handle to avoid accidents.

ALPA design Hammer Pulverizer of Sodium Gluconate applied a very good reputation in actual production applications, and also won the praise of users and friends. If you need to buy Hammer Pulverizer of Sodium Gluconate, please feel free to contact us.