Vibration Mills for peanut shells

good balance of performance Vibration Mills for Peanut shells, just need to place it can be produced on a stable ground, and low noise, dust leakage problems can be avoided in the process of crushing, powder favored by the industry.

What factors will affect Vibration Mills for performance parameters Peanut shells to use it?

The following is a detailed description:

1 Control feed size

Most Vibration Mills for Peanut shells on the feed size limit certain requirements. After entering the pulverization cavity, it can be sufficiently accelerated before collision and crushing with other particles. It is difficult to completely accelerate after large particles enter the pulverized cavity, which will allow them to stay in the machine too long, resulting in too high energy consumption. Therefore, in large-scale production of ultrafine powder, it is an effective way to pre-ground the raw material of the particle size is an effective pathway for energy saving.

2. Working medium

Currently, Vibration Mills for Peanut shells main working medium is compressed air, superheated steam, inert gas. The choice of working fluid has a certain impact on crushing effects and economics. Superheated steam is superior to air in fluidity and critical flow rates to achieve higher flow rates and uniform flow fields. However, using superheated steam as a working fluid, it must be ensured that it is still in an overheating state before entering the product capture device, otherwise the material is condensed.
3. Feeding speed

Feeding speed is an important parameter reflecting gas flow grinding production capacity. During the pulverization process, the optimum ratio of the intake flow rate and the feed speed is the key to improving the crushing efficiency. In general, under certain intake flow conditions, the feed speed is proportional to the particle size of the product. However, the feeding speed is too fast, which will increase the particle density, mutual interference, disadvantage of the particles, and difficult to achieve the sufficient and effective collision between particles, affect the crushing effect; although the feed speed is too slow, the particles stay in the crush area The time can be extended, which will reduce the particle density, reduce the collision rate, resulting in a decrease in production capacity and an increase in unit production energy consumption.

4. size limit

Vibration Mills for Peanut shells during the comminution process, the material with decreasing particle size, uniformity and intensity crystalline material is increased. After reaching a certain degree, the particle size of the material is no longer reduced or reduced, that is, the crushing limit of the material is reached. In this case, the material specific surface area increases, increased activity of the particle surface, agglomeration between the particles and the polishing state of dynamic equilibrium, even if the extended grinding time, it is difficult to further reduce the materialParticle size.


ALPA desulfurizer Vibration Mills for peanut shells case sharing: The company is a high-tech company that requires a desulfurizer crusher, investigating a number of powder equipment manufacturers at home and abroad, Finally, we chose our AlPA's Vibration Mills for Peanut Shells.

Finished granularity: 200 mesh 90% By
Production capacity: 4-5T


In the production process, the temperature rise of the bearing must often be checked. When it is more than 50 ° C, it should be stopped, and the reason is to rule out the fault. When the new machine is running, the drive belt is easy to elongate, pay attention to adjust the proper looseness of the belt to ensure the work life of the belt. If the lifting piece should be checked frequently, replace the production quality and production in time. The blade, the bushing should often check the wear situation. If the wear is worn, the productivity decreases, and the particle size is roughly discovered to be replaced. The host and the grading flow bearing are lipomatic lubrication, using special lipids, the replacement period of the bearing is around three months, and the filling of the grease is 1/2 of the interior space in the bearing cavity. Otherwise, It will cause too high of the bearing temperature. The spiral feeder has changed the lipid period of half a year, and Cape Calcium-based grease. In the output shaft E, ie the pulley E, avoiding the weight of the weight, damage the part. It is strictly forbidden to turn the handle on the stop. The lubricating oil used in this regulator is used with N32 alkaline high-zinc high-grade anti-motor oil pressure oil, and the deceleration machine is 401 generally lubricating oil, and it is not necessary to use other machines. After four or five months, new oil should be replaced.